Sensors

Showing all 16 results

  • 2-Meter Double- Terminated Cable

    $100.00
    Add to cart

    2-Meter Double- Terminated Cable

    2 Meter cable with male connector at each end

    SKU: TSM - 2M Cable Category:
    $100.00
  • 5-Meter Double- Terminated Cable

    $115.00
    Add to cart

    5-Meter Double- Terminated Cable

    5 Meter cable with male connector at each end

    SKU: TSM - 2M Cable-1 Category:
    $115.00
  • FlexSCADA RS232 Adapter

    $80.00
    Add to cart

    FlexSCADA RS232 Adapter

    (Includes null modem adapter) to accommodate direct serial connection to many MorningStar Charge Controllers* allowing implementation & communication of the modbus RTU serial protocol spec. *Please consult customer service prior to ordering to ensure compatibility

    Category:
    $80.00
  • High Voltage Reducer (HV10M)

    $40.00
    Add to cart

    High Voltage Reducer (HV10M)

    The new din-rail mountable High Voltage Reducer (HV10M) enables the FlexSCADA Q5 to measure voltages beyond 60 volts. The redesigned HV10M allows users to monitor more inputs and increases the maximum voltage range from 60V to 300V. HV10M connectors are rated to 300V and the voltage scaling components are rated to 1.5kv, providing protection against large surges and
    transient events.
    Utilizing the upgraded HV10M, the FlexSCADA Q5 can now monitor voltages from each of the eight (8) analog inputs. Input lines can be connected directly to the terminal blocks and into the HV10M, eliminating the need to remove the terminal block to connect input wires to the high voltage reducer. The improved HV10M is also physically larger than the original version, both to facilitate din-rail mounting and to allow the unit to accept larger gauge input wire. As voltage reduction occurs within the unit, large gauge wire is not required to connect the HV10M to the analog input of the FlexSCADA Q5.

    Category:
    $40.00
  • MCE-ARS Wind Turbine Stop Switch

    $299.00
    Add to cart

    MCE-ARS Wind Turbine Stop Switch

    The Mission Critical Energy Automatic Remote Stop-Switch (MCE-ARS) provides a means to remotely shut down a wind turbine based on environmental conditions. When combined with a FlexSCADA Q5 and a wind speed indicator (such as the Anemoment TriSonica™ Mini Wind and Weather Sensor) any wind turbine can be made fully autonomous, providing the user with peace of mind that the system will remain protected unsupervised during the harshest conditions. User selectable to work with 24 VDC or 48 VDC systems, the MCE-ARS builds on the success of the early versions of the SW35x-ARS, while improving on the design, functionality and stability of the device.

    The MCE-ARS measures 4.5 inches long, 3.5 inches wide and 1.5 inches tall.

    Category:
    $299.00
  • TriSonica Mini Wind and Weather Sensor

    $1,350.00
    Add to cart

    TriSonica Mini Wind and Weather Sensor

    The world’s smallest and lightest 3D ultrasonic anemometer. The TriSonica Mini Wind and Weather Sensor optimizes size, weight, and power (SWaP) variables and is both reliable and accurate in a variety of applications where monitoring of atmospheric conditions is required. Compact and maintenance free, their no moving parts design makes them ideal for both portable, temporary deployments, as well as permanent installations.

    Category:
    $1,350.00
  • TSM FlexSCADA Kit

    $1,850.00
    Add to cart

    TSM FlexSCADA Kit

    When combined with the FlexSCADA Q5, the TriSonica Mini Wind and Weather Sensor FlexSCADA Kit not only provides wind statistics (wind speed, direction, temperature, moisture borne in the wind, dew point, and air density), but also allows users to autonomously monitor and control their micro wind turbines, enabling remote and automatic shutdown of turbines during high wind events.

    Kit includes a Trisonica Mini sensor, a FlexSCADA conversion box, a 2 or 5 meter interfacing cable (selected at checkout) and a 22mm carbon fiber mounting tube.

    Category:
    $1,850.00
  • Flexs Q5 DC Power Distributor

    $30.00
    Add to cart

    Flexs Q5 DC Power Distributor

    Converts the Flexs Q5’s 8 relay switches into 8 switched dc power ports which draw power from the 2 pin screw terminal. Allows for simplified installation removing the need for a separate bus bar when all loads can be powered from a common source. Do not purchase the part if you require low side switching or more complicated switching configurations.

    SKU: ACC-Q5-DIST15A Categories: ,
    $30.00
  • Flexs Q5 High Voltage Reducer

    Read more

    Flexs Q5 High Voltage Reducer

    This inline voltage reducer is designed to all you to measure voltages beyond 60V from the Flexs Q5. It connects inline between your voltage source and the input channel on the Flexs Q5 increasing the maximum voltage range from 60V to 300V. The connectors are rated at up to 300V and the voltage scaling components up to 1.5kv providing protection against large surges and transient events.

  • Q5 Series Split Power Distribution Panel

    $35.00
    Add to cart

    Q5 Series Split Power Distribution Panel

    The Q5 Series Split Power Distribution Panel

     

    Converts the Flexs Q5’s 8 relay switches into 4 dedicated switched DC power ports at 12, 24 or 48V, and allows the other four ports to be dedicated a different voltage output.  For example, four at 24V and four at 48V.  Both power ports sides draw power from opposing the 2 pin screw terminals.

    Allows for simplified installation removing the need for a separate bus bar when all loads can be powered from two common voltage sources.

    SKU: ACC-Q5-SPDST15A Categories: ,
    $35.00
  • Current Sensor (Bi-directional) Non Invasive Amp Coil Style up to 100A [Flex 4 & 5 OLD Style]

    $30.00
    Add to cart

    Current Sensor (Bi-directional) Non Invasive Amp Coil Style up to 100A [Flex 4 & 5 OLD Style]

    This 100A Bi-Directional, Non Invasive current allows you to safely measure electrical current direction and amperage.  Note: If you are replacing an old style (pre-2018 current sensor, this is a 1 to 1 replacement, however we highly recommend the new version; ACC-ACS100DR)

    SKU: ACC-AMP100NI Category:
    $30.00
  • Irradiance sensor

    $385.00
    Add to cart

    Irradiance sensor

    (Si sensor) are a cost-effective, but rugged and reliable solution for the measurement of solar irradiance, especially for the monitoring of Photovoltaic (PV) systems. Based on the construction of the sensor element corresponding to a PV module they are ideal as reference for the monitoring of PV systems. Especially the spectral response comparable to PV modules as well as the similar inclination error (incident angle modifier) allow an exact analysis of PV energy yields using Si sensor data. Power supply needed: 12 to 28 VDC. Output 0 to 10 V. Range 0 to 1,500 W/m

    SKU: SI-V-10TC Category:
    $385.00
  • Non Invasive Amp Coil Sensor (Bi-directional Current) rated up to 100A

    $45.00
    Add to cart

    Non Invasive Amp Coil Sensor (Bi-directional Current) rated up to 100A

    NEW!!!  100A Bi-Directional, Non Invasive current with higher accuracy and is Din Rail mountable – allows you to safely measure electrical current direction and amperage. This Current sensor is more durable and accurate than previous versions, and is Made in Canada.

    SKU: ACC-ACS100DR Category:
    $45.00
  • Wind speed sensor with impulse output

    $225.00
    Add to cart

    Wind speed sensor with impulse output

    Sensor type: Cup star anemometer Signal:Reed relays, 2.5 Hz/(m/s) Range:0.9 to 40 m/s(60 m/s for short time)Accuracy :0.5 m/s or 5% of reading Ambient temperature:-25 to +60°C (without icing) Cable:3m LiYY, 2 x 0.22 mm2, black, weather and uv-resistant. Includes Mounting Plate.

    SKU: Vwind-Imp Category:
    $225.00
  • Waterproof Digital Temperature Sensor Probe 1 meter

    $20.00
    Add to cart

    Waterproof Digital Temperature Sensor Probe 1 meter

    The DS18B20 is a ULTRA HIGH resolution LOW POWER digital temperature sensor, these are pre-installed into a rugged and waterproof stainless steel enclosure allowing for a variety of installation scenarios. These sensors each contain unique address allowing up to 32 of them to be directily connected to our Flexs series PLC’s with only 3 wires

    SKU: ACC-TEMP1M Category:
    $20.00
  • Waterproof Digital Temperature Sensor Probe 3 meter

    $25.00
    Add to cart

    Waterproof Digital Temperature Sensor Probe 3 meter

    The DS18B20 is a ULTRA HIGH resolution LOW POWER digital temperature sensor, these are pre-installed into a rugged and waterproof stainless steel enclosure allowing for a variety of installation scenarios. These sensors each contain unique address allowing up to 32 of them to be directily connected to our Flexs series PLC’s with only 3 wires

    SKU: ACC-TEMP3M Category:
    $25.00
Menu